VEVOR Shop Press Buying Guide (2026): H-Frame Hydraulic and Arbor Presses, 17 Picks from 70,90 €, and Why a “20 Ton” Press Can Be Rated 13.3 T

A shop press pushes a ram down with a lot of force: to press bearings and bushings in and out, swap U-joints and ball joints, straighten a bent bracket or flatten a part. VEVOR sells two kinds. Arbor presses are cast-iron benchtop tools with a rack-and-pinion lever: fast, precise, no hydraulics, but 0.5–3 tons at most. H-frame hydraulic presses use a bottle jack or cylinder for 6 to 50 tons; the bigger ones add an air-assist pump. On November 9, 2026 we kept 17 in-stock presses from 70,90 € to 1.356,90 €: 5 arbor presses, 1 benchtop hydraulic press, 5 manual floor presses and 6 air-assisted or two-speed presses. The useful numbers are the rated load (not the “max”), the opening height, the stroke, and the delivered price.

• The 17 picks at a glance
• Price traps
• Rated vs maximum load
• Tons, opening and stroke: what size you need
• Air assist and compressors
• Safety basics
• Who each one is for
• FAQ

The 17 VEVOR shop presses at a glance

Arbor presses (cast iron, lever, benchtop)

Benchtop hydraulic press

Manual H-frame floor presses (10–20 T)

Air-assisted, two-speed and big presses (20–50 T)

Price traps (our arithmetic)

• “12 Ton” that is rated 8 T: the bottle-jack G is 277,99 € and its spec table says “Rated Load 8 T”, “Maximum Load 12 T”. The triangular-base H is 265,90 € on a deal until Nov 18 (286,90 € before), so it is now 12,09 € cheaper, and its table says “Rated Load” 12 ton. Per rated ton that is 34,75 € vs 22,16 €.
• The same trick at 20 tons: J (410,90 € on a deal until Nov 18, was 439,99 €) is “20 Ton” in the title but “Rated Load 13.3 T”, “Maximum Load 20 T” on the sheet; K (448,90 €) lists “Rated Load 20T”. While the deal lasts, 38,00 € more buys about 50% more rated load (13.3 vs 20 T): 30,89 € vs 22,45 € per rated ton (before the deal the gap was 8,91 €). The air-assisted L and O and the two-speed M are also 13.3 T rated / 20 T max.
• 10 tons for 18 € less than 20: the 10 T I with a separate hand pump is 430,90 €, just 18,00 € under the 20 T K and 152,91 € over the “12 Ton” G. Its spec table also repeats a 770 × 596 × 1770 mm size (the same as the 20 T air press N) while listing a 58–383 mm working height and 39.7 kg, so confirm the real size with VEVOR before you plan bench space.
• 40 € shipping on every floor press: with Romania as the delivery country, G becomes 317,99 €, H 305,90 € at the deal price; the 6 T benchtop F ships free at 113,90 €. If 6 tons and a 55–250 mm opening are enough, that is 192,00 € less than the delivered 12 T H.
• Air assist costs 281 €: the 20 T manual + pneumatic N is 729,90 €, 281,00 € more than the manual 20 T K with the same “ZX0901 item 20T” model line. The manual/pneumatic L is 564,99 € (116,09 € over K, but rated 13.3 T); the foot-pedal O with 9 punches is 195,00 € more than L, and the two-speed M adds 46,00 € over L for a fast approach ram instead of air.
• 30 T for 45 € more, 50 T for 582 € more: P (30 T, 774,90 €) is only 45,00 € over the 20 T air press N. Q (50 T, 1.356,90 €) adds 582,00 € and weighs 215 kg. Per rated ton: N 36,50 €, P 25,83 €, Q 27,14 €, against 22,45 € for the manual K.
• A 3 T arbor press costs more than a 12 T hydraulic one: D is 329,90 € + 40 € shipping = 369,90 €, 256,00 € more than the free-shipped 6 T F. You pay for speed, precision and a 310 mm stroke, not force. The ratchet version E adds 100,00 € (same 310 mm stroke and 166 mm plate) and shows 2.8 stars from 13 reviews.
• Small arbor presses: 2 € for twice the force: the 0.5 T A (70,90 €) and the 1 T B (72,90 €) are 2,00 € apart, and B also lists 150 mm stroke instead of 119 mm. The handwheel 1 T C costs 14,00 € more than B for the same 150 mm stroke and 90 mm plate.

Rated load vs maximum load

The newer VEVOR listings (G, J, L, M, O) print two numbers: a rated load you can use all day, and a maximum load where the relief valve opens. The title uses the maximum. Rated is about two thirds of it on these sheets (8 of 12 T is 67%, 13.3 of 20 T is 66%; our arithmetic). The older orange and blue listings (F, H, I, K, N, P, Q) print a single “Rated Load” that matches the title, and VEVOR’s text on H says the relief valve opens “when the pressure exceeds 12T”. Two sheets written differently are not proof of two different jacks, but compare rated with rated, and size the press so your normal job sits well under it.

Tons, opening and stroke: what size you need

• Tons: stuck wheel bearings and hub bearings on cars usually need a 12–20 T floor press; small bushings, pulleys and U-joints often go with 6–12 T; rivets, leather stamping and small bearings fit a 0.5–3 T arbor press. If a part does not move near the rated load, stop and check for a missed circlip or rust rather than adding force.
• Opening (working height): F opens 55–250 mm, I 58–383 mm, H 40–705 mm, K 50–830 mm, N 65–1030 mm. A knuckle or a long shaft needs the taller frames. Width between the posts matters too: VEVOR answers 410 mm on H and 520 mm on K.
• Stroke: the ram only travels 110–190 mm on the hydraulic presses, so you move the bed with the pins and use spacers. VEVOR warns on several listings: “Exceeding the cylinder stroke range may cause damage to the cylinder seals.” Arbor presses travel 119–310 mm without resetting.
• Weight and space: from 22 kg (F) to 215 kg (Q). The floor presses need a level concrete floor, and the bigger ones should be bolted down.

Air assist and compressors

The air-assisted presses (N, P, Q, and L/O in air mode) list a pump operating pressure of 0.8–1.2 MPa, which is 8–12 bar. Many small home compressors stop at 8 bar, so check yours before you pay 281,00 € for air assist; you can still pump every one of them by hand. Our VEVOR air compressor guide lists tank sizes and pressures. The two-speed M is a different idea: a large ram (rated 1.33 T) closes the gap quickly, then the small ram does the 13.3 T rated work, no compressor needed.

Safety basics

Who each one is for

• Leather, rivets and small bushings on a budget: VEVOR 0.5 ton manual arbor press (AP-0) (70,90 €).
• Small bearings and bushings, the sensible arbor press: VEVOR 1 ton manual arbor press (AP-1) (72,90 €).
• Tall parts on a bench, long-stroke arbor press: VEVOR 3 ton manual arbor press (AP-3) (329,90 €).
• Cheapest hydraulic press, free shipping: VEVOR 6 ton benchtop H-frame hydraulic shop press (113,90 €).
• Home garage, 12 tons rated: VEVOR 12 ton H-frame floor shop press, triangular base (265,90 € deal until Nov 18).
• Home garage, 20 tons rated: VEVOR 20 ton H-frame floor shop press, triangular base (ZX0901 20T) (448,90 €).
• Tall parts, air assist with an 8–12 bar compressor: VEVOR 20 ton manual + pneumatic H-frame shop press (ZX0901 20T) (729,90 €).
• Fast approach without a compressor: VEVOR “20 Ton” shop press with two-speed pump and gauge (ZX0901F-7) (610,99 €).
• Workshop with heavy parts, 30 tons: VEVOR 30 ton manual + pneumatic H-frame shop press (ZX0901 30T) (774,90 €).
• Truck and agricultural work, 50 tons: VEVOR 50 ton manual + pneumatic H-frame shop press with winch (ZX0901 50T) (1.356,90 €).

Related on SiftGuide

More garage and workshop tools: the VEVOR floor jack guide, the VEVOR air compressor guide, the VEVOR drill press guide and the VEVOR torque wrench guide.

FAQ

Arbor press or hydraulic press?
An arbor press is quick and precise for light work up to its 0.5–3 T rating, with no oil to leak. A hydraulic H-frame press gives far more force (6–50 T) for bearings, ball joints and straightening, but each stroke is slow and short.

Which tonnage should I trust?
The rated load. On G, J, L, M and O the rated load is clearly printed (8 T or 13.3 T) next to a higher maximum; on the other hydraulic listings the single figure is labelled “Rated Load”.

Do the prices include shipping?
Not always. On November 9, 2026, A, B, C and F showed free shipping to Romania; all other presses showed 40,00 € shipping on top of the price. Estimates were 11–16 November.

Do I need a compressor?
No. Every press here can be pumped by hand; the air-assisted ones just make long jobs easier and list 8–12 bar air.

Sources: VEVOR EU product pages, spec tables and Q&A answers of the listings linked above (arbor AP-0, AP-1, APR-1, AP-3, APR-3; hydraulic 6 T benchtop, ZX0902FA, 12 T triangular base, ZX0901 10T/20T/30T/50T, SJ-026, ZX0901F-8, ZX0901F-7, SJ-26SQB), checked on November 9, 2026. A 6 T bottle-jack press (ZX0904C) was out of stock and is not listed. Prices in euros, VAT included, as shown with Romania as the delivery country. Price differences, delivered prices, euros per ton and percentages are our own arithmetic.